In recent years, with the rising trend of LCD TVs in the home appliance industry and the outstanding performance of LCD screens, the application of LCD splicing screens in the field of large-screen monitoring has gradually attracted attention and gradually become the mainstream of the market. However, if the screen of the LCD splicing screen continuously plays the same picture for a long time, the pixels in the area where the brightness is too high may be burned out, and the screen aging may also be accelerated. Here is a small series to teach everyone how to anti-aging LCD splicing it.
Method one: Let the LCD splicing screen rest intermittently
LCD splicing screens can easily overheat certain pixels due to prolonged work. Once it exceeds the limit, it will cause permanent damage. This creates a “bad point.†Because the pixels of the LCD splicing screen are composed of liquid crystals, Therefore, when it is continuously working at full load, it will accelerate its aging and even burn out in serious cases. Therefore, if the user must work for a long time, it is best to intermittently allow the LCD splicing screen to rest for a while, this effort can not only delay the aging of the LCD screen, but also to avoid hardware damage.
Method two: Change the screen display often
If the screen of the LCD splicing screen continuously plays the same picture for a long time, the pixels in the area where the brightness is too high may be burned out, and the aging process of the screen may also be accelerated. In the process of use, the screen displayed on the lower screen is often changed. This will not cause a certain pixel to be burned due to heat, which can protect the screen to a certain extent and delay its aging.
Method 3: Work in the screen saver mode for a while
The higher the color saturation, the brighter the displayed image.
· The resolution determines the clarity of the picture, the resolution of the LCD is relatively high, the picture is more delicate, and more content can be displayed.
The liquid crystal has high luminous efficiency and relatively low power consumption.
· The life span of LCD and rear projector is only related to the light emitting part. Replace the backlight tube or replace the bulb after the expiration date. However, the lifetime of the plasma is related to the screen. After the expiration, it can only be scrapped and cannot be used.
• The burn phenomenon manifests itself as a shadow on the screen when the still image stays in a position for a long time. The display principle of liquid crystal and projection determines that the screen will not burn, but the phenomenon of plasma burn is more serious, which is entirely caused by the principle of plasma gas light.
Method one: Let the LCD splicing screen rest intermittently
LCD splicing screens can easily overheat certain pixels due to prolonged work. Once it exceeds the limit, it will cause permanent damage. This creates a “bad point.†Because the pixels of the LCD splicing screen are composed of liquid crystals, Therefore, when it is continuously working at full load, it will accelerate its aging and even burn out in serious cases. Therefore, if the user must work for a long time, it is best to intermittently allow the LCD splicing screen to rest for a while, this effort can not only delay the aging of the LCD screen, but also to avoid hardware damage.
Method two: Change the screen display often
If the screen of the LCD splicing screen continuously plays the same picture for a long time, the pixels in the area where the brightness is too high may be burned out, and the aging process of the screen may also be accelerated. In the process of use, the screen displayed on the lower screen is often changed. This will not cause a certain pixel to be burned due to heat, which can protect the screen to a certain extent and delay its aging.
Method 3: Work in the screen saver mode for a while
The higher the color saturation, the brighter the displayed image.
· The resolution determines the clarity of the picture, the resolution of the LCD is relatively high, the picture is more delicate, and more content can be displayed.
The liquid crystal has high luminous efficiency and relatively low power consumption.
· The life span of LCD and rear projector is only related to the light emitting part. Replace the backlight tube or replace the bulb after the expiration date. However, the lifetime of the plasma is related to the screen. After the expiration, it can only be scrapped and cannot be used.
• The burn phenomenon manifests itself as a shadow on the screen when the still image stays in a position for a long time. The display principle of liquid crystal and projection determines that the screen will not burn, but the phenomenon of plasma burn is more serious, which is entirely caused by the principle of plasma gas light.
Led Iron Panel Light,Led Round Iron Ceiling Light,Led Ceiling Light Round,Led Adjustable Panel Light
Foshan Extrlux Co., Ltd. , https://www.extrlux.com