Today, when floors are used for a long time, they need to be regularly waxed and maintained to extend the life of the floor. Waxing the floor can remove stubborn stains on the floor. By waxing, the material itself is isolated from the air, and the damage caused by oxidation or contact with harmful substances in the air is reduced, so that the purpose of prolonging the service life of the material and the beauty of sightseeing can be achieved. So do you know how the waxing of the floor is going on? Do you understand the process of waxing floors ? The following small series will take you to understand some of the floor waxing knowledge.
Floor waxing introduction
Waxing on the floor is to solid wood floor, pvc (plastic) floor, stone floor (marble, granite, terrazzo), etc., on the surface coated with a layer of wax, the wax is cured and isolated from the air, water vapor, dust, while also playing a non-slip , anti-wear, anti-static effect, so as to better maintain the floor and extend the life of the floor. Waxing is divided into: playing solid wax and liquid wax two. Waxing floor requires professionals, wax layer, wax liquid to be evenly distributed, moderate thickness, so as to achieve bright and clean floor effect.
Floor waxing method
1. Clean up the garbage and debris on the ground and erect a construction sign. Wipe the stain on the floor with a diluted neutral detergent. For difficult-to-remove stains, please clean with water. To prevent the detergent from accumulating in the grooves, the rag soaked with detergent should be wrung out as much as possible. Floor wax scavengers can cause floor stains and bulging and must not be used.
2. Clean the floor with a neutral detergent and a floor washer. Wipe with a well-wrung rag. The surface of the floor, especially the grooved part, should be carefully wiped and there should be no residual detergent. If there is residual detergent and moisture, the surface will be whitened and bulging.
3. Dry the floor with a dry towel or wait for it to dry naturally. Dry the surface of the floor and the water in the groove fully dry enough for waxing. According to the season, the time required will change, but it will take more than half a day. If not fully dried, the floor wax will not adhere closely to the floor surface, affecting the appearance and causing whitening.
4, wait until the ground is dry, and then evenly wax the surface. Shake the container with floor wax and stir well. Apply it carefully in the direction of the wood grain of the floor, without missing paint or uneven thickness. Excessive smearing will cause uneven shades and excessive smearing that will result in poor film formation. Keeping thin and even is the key to waxing. Do not dilute the floor wax with water. Waxing tools can be used for waxing mop, easy to operate, and ideal results.
5, wait until the wax surface is completely dry, by the professional with a high-speed polishing machine with the polishing pad polishing to the surface brightness can be uniform.
6. The floor after waxing and polishing is bright and clean, and the sensory effect is particularly good. Do not walk on the floor before drying the floor wax. Drying usually takes 20 minutes to 1 hour. If there is a leak, apply it. Such as the use of waxing twice, the second time, after the first complete drying. Wax once every 6 months or so can keep the floor beautiful for a long time.
Floor waxing manipulator
1, vacuum: in addition to the floor surface of the fixture and some adhesives, rubber, cement, paint, etc.
2. Cleaning: electric mop, sauna machine, sterile, clean, no damage to the floor
3, Waxing: For different floors, use different waxes, all parts with wax
4, polishing: professional operation + polishing machine is completed
Waxing on the floor:
1, protect the floor;
2, increase the appearance;
3, anti-skid;
4, easy to clean:
Ground analysis:
1, hard ground granite, marble, terrazzo (base wax and surface wax two times better) mirror tile, porcelain tile, glazed tile (waxing effect is not good, easy to fall off)
2. Soft floor rubber floor series, PVC material floor series 3, wooden floor series solid wood floor, composite floor. Note: For soft floor and Wood Flooring series, if waxing treatment is required, it is better to use anti-abrasive high gloss wax without polishing. Wood floor waxing tools: washing machines, suction machines, high-speed polishing machines, air drying machines, wax or tiger clips, towels, water presses, work signs and rags.
Wood floor waxing agent: high-speed polished surface wax, bottom wax, surface-free wax, floor cleaner (acid cleaner, all-around water) or wax water, neutral
Waxing floor notes:
First, in order to prevent the detergent from accumulating in the grooves and let the wood soak the detergent, the used wipes need to be wrung out without water stains. When using wax scavengers on some floors, it may cause traces or bulges on some floors. At this time, it should be noted that it needs to be wiped with a wrung rag.
Second, before the waxing, be sure to pay attention to the floor fully dried: if not fully dried, the floor wax will not be tightly attached to the floor, so it will affect the beauty, let the floor produce white phenomenon.
Third, play wax at least three times, and infiltrate the wood with a lint-free cloth each time.
Fourth, a simple polish can be performed for each wax.
Fifth, each time the wax is applied to the floor, wait until after drying, you can use a very fine sandpaper to polish the appearance.
Sixth, wood floor waxing tools: steel wool, sponges, rags, vacuum cleaners, home wood floor waxing, floor wax.
Floor waxing routine maintenance
1. Spray the dust with the electrostatic liquid in the sprayer at the bottom of the dust, and push the dust when it is air dried. (After the electrostatic dust remover, the vacuum function will not damage the wax surface);
2, when the surface of the wax stains with neutral all-purpose cleaner with water to 1:10 ratio dragging the surface can not be used to clean water drag wax surface;
3, the wax is not lit with dust and stains can be polished that is bright as new.
Editor's summary: The relevant information on the floor waxing process was introduced here for everyone. I hope this article will be helpful to everyone. If you still have something you don't understand, you can leave a message to Xiaobian at the bottom. We will answer your questions as soon as possible.
Waxing on the floor
Blockboard is a multi-ply board with a block core. This gives the board optimum flatness of each panel as well as a high resistance to wrapping. Blockboard is obtainable in both lightweight and heavyweight, where by the heavyweight board is normally classed as laminboard.
Luli Group Co., Ltd, is a leading supplier if wood panel products since year 1985, has the capability and capacity to produce high quality blockboard yet with competitive pricing. And we are able to assist you at all time with professional handling.
Advantages of Blockboard:
High dimensional stability
Termite and borer resistant
Stable in all weather conditions
The details of Blockboard:
Sizes: 1220mm x 2440mm(Standard Size), 1250mm x 2500mm or according to customer`s request.
Thickness: 15mm, 16mm, 17mm, 18mm, 19mm, 20mm, 22mm, 25mm, etc.
Core: Falcata/Malacca, paulownia, eucalyptus, fir, poplar, pine, birch, hardwood, etar, pine, birch, hardwood, etc.
Density: 450kg ~ 680kg/m3
Blockboard
Batten Blockboard,18mm Blockboard,Laminated Blockboard,Blockboard Price
Luli Group Co.,Ltd. , https://www.plywoods.nl