Many families favor the installation of wooden flooring, and the word on the floor industry has been rumors: "Three-point floor, seven-point installation" shows the importance of wood floor installation. There are four commonly used wood floor installation methods . Each laying method can be selected due to people, place, and function. Let's take a closer look at the wood flooring installation method .
A wooden floor installation method - keel laying method
First lay the keel, and according to the laying direction and length of the floor, pop up the keel laying position. Each floor rests on at least 3 keels, generally not more than 350 mm apart. Then, the wooden keel is fixed. When the difference in the height of the local surface is too large, the leveling of the studs is to be done. The studs are fixed to the concrete base layer with the nails, and the wooden keel is fixed on the studs with nails. If the ground is under the water pipes or floor heating and other facilities, do not hit the eye, you can use steel, aluminum alloy keel and other new keel, or use adhesive to bind short wood keel.
The floor covering is generally laid out in a wrong position. After a gap of 8-10 mm is left from the side of the wall, the first row of wooden floor is laid and the outside of the floor is convex. The floor is fixed on the wooden keel by screws and nails. Afterwards, they are tightened one by one. Every part of the wooden floor that touches the wooden keel must be screwed in with an air gun spike, a threaded screw, or an ordinary nail. The length of the nail must not be shorter than 25 mm.
Scope of application: Generally speaking, this installation method is mostly used for solid wood flooring and solid wood composite flooring.
Second, wood floor installation method - suspension laying method
The direction of paving wood floors is generally the same as the direction of the room's walking, and paved one by one from left to right or from right to left. Grooves are placed between the wall, the wooden wedge between the floor and the wall, and the expansion joints are left. In dry areas, the floors are wet and the expansion joints should be kept small; in damp areas, the floors should be dry and the expansion joints should be large. In the trial shop should observe the board surface height difference and gap, at any time to adjust, check qualified before sizing installation. Generally, several rows of water-proof and environment-friendly adhesives can be fixed on the edges, and the rest of the middle part is completely meshed with the tongue and groove without sizing. The last row of floors is cut, glued and measured by measuring its width and tightened with pull hooks or screw tops.
Scope of application: Generally, it is mostly used for the floorboards with high quality and double floor.
Third, the wood floor installation method - plywood laying method
The plywood keel laying method is to lay the keel first, then lay the wool floor on the top, fix the wool floor and the keel, and then lay the floor on the wool floor. This not only enhances the moisture resistance, but also makes the foot feel more comfortable and soft. However, the loss of more layers is higher than other methods.
The laying method is that the wool floor is laid on the keel, and there should be gaps between each row. The floor and the keel are fixed and leveled with iron nails or screw nails. The wool floor can be laid at an oblique angle of 30 degrees or 45 degrees to reduce the stress. . Laminated flooring is laid on the wool floor and laid according to the suspended laying method.
Scope of application: Can be used for a variety of floors, such as solid wood flooring, engineered wood flooring, laminate flooring and cork flooring.
Fourth, wood floor installation method - paste laying method
For the laying of solid wood and cork flooring below 30 cm in length, some small pieces of teak and parquet flooring must be laid directly. If the cement floor is laid directly, it must be leveled with cement. Compared to the leveling of paving slabs, it will not affect the height of the house too much. However, if cement is used for leveling, a lot of cement and sand will be used and the cost will be higher. If cork flooring is used, it is recommended to make self-leveling cement mortar on the original foundation.
Scope of application: parquet flooring, cork flooring, and composite wood flooring.
Summary: Several common wooden floor installation methods are introduced here for everyone. Different floor installation methods are also different. Therefore, before the renovation, you must first know which type of floor you are using, which is more convenient to reserve and shop. It is also more convenient to put together.
Wood floor installation method
Large Coal Stove,Outdoor Camping Wood Stove,Freestanding Wood Burning Stove,Cast Iron Coal Stove
Jinan Huancheng Heating Equipment Manufacturing Co., Ltd. , https://www.globalstove.com