Who decides the life of the prefabricated direct buried insulation pipe?

During the pipeline installation and installation process, the two pipes are not tightly welded to cause water seepage, or the operation is not serious in the process of “filling the mouth”, causing damage caused by external sewage infiltrating into the insulation layer.

In the current building decoration materials, the prefabricated direct-buried insulation pipe is an indispensable element. Its high-quality insulation performance can effectively prevent the penetration of water, moisture and other corrosive liquids and gases, and prevent microorganisms. The growth and development of adaptable polyurethane foams can be firmly bonded to a variety of materials. The temperature of the prefabricated direct buried insulation pipe is -50 °C ~ +150 °C, and the short-term (ten hours) can reach +190 °C.

The main factors affecting the life of prefabricated direct buried insulation pipes are as follows:

1. The prefabricated direct buried thermal insulation layer is inconsistent with the steel pipe to form uneven thickness of the insulation. In severe cases, the outer plastic can be softened and damaged.

2. It is vulnerable to damage during transportation and installation. It is not deep enough from the ground after the burial or the upper soil and road are soft, which causes the load vehicle to be damaged after being crushed.



3. The foaming temperature of the prefabricated direct buried insulation pipe is not suitable. Foaming is carried out by heat, and if there is no heat, the blowing agent in the system cannot evaporate, so that foam cannot be formed. Heat comes from both chemical reaction generation and environmental supply. The heat of chemical reaction is not affected by external factors, and the heat provided by the environment changes with the change of ambient temperature. When the ambient temperature is high, the environment can provide heat to the reaction system, which can increase the reaction rate and shorten the reaction time.

4. The interface is not properly handled. During the pipeline installation and installation process, the two pipes are not tightly welded to cause water seepage, or the operation is not serious in the process of “filling the mouth”, causing damage caused by external sewage infiltrating into the insulation layer.

5. The plastic and polyurethane materials used are unreasonable. For example, it is often found that the plastic pipes which are extruded and formed are not sufficiently plasticized to deteriorate the outer tube. The low density of the polyurethane insulation tube results in low strength and is damaged during the handling process. In addition, the free acid contained in the system is too high, causing corrosion on the outer wall of the steel pipe.
Langfang Xinda Insulation Materials Co., Ltd. is a modern industrial enterprise specializing in the production and sales of prefabricated direct buried insulation pipes and direct buried prefabricated insulation pipes. The products are of high quality and low price. The company sincerely welcomes new and old customers to come to the company to negotiate business.

Http://news.chinawj.com.cn Who decides the life of the prefabricated direct buried insulation pipe? Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn Who decides the life of the prefabricated direct buried insulation pipe?

Melamine Particle Board is mainly used for furniture and carriage of bus, train.The bace&back are the Veneer surface, such as Okoume, Bintangor, Pine, Birch, Poplar, Pencil cedar, Maple, Cherry, White Oak, Sapele, Beech, Red Oak, Ash etc.Melamine paper is the most popular to be as the face board, it is abrasion resistant, heat resistant, fouling resistant, clean is simple.The Engineering Wood is also as the face and back surface. It is more cheaper and beautiful, can reach the same wood grain effect as the veneer surface.And we have High Quality Particle board .LULI Group Co. Ltd, well known as the leading manufacturer for wooden, steel and paper products, located in Shouguang, Weifang, Shandong, China. Since the foundation in 1985, it focus on the production of Plywood , venner, MDF , Particle Board ,  Door Skin , Blockboard , Finger joint board, OSB , paper, Steel etc.And we have Outdoor Melamine Particle Board.

Melamine Particle Board Details:

size:1220*2440MM 1250*2000MM 1525*2440MM 1830*2440MM

THICKNESS:9MM-40MM

MATERIAL:POPLAR, COMBINE, PINE

GLUE:E0, E1, E2

CERTIFICATION:CARB, FSC, CE

Melamine Particle Board

Melamine Particle Board,Melamine Faced Particle Board,Outdoor Melamine Particle Board,Melamine Laminated Particle Board

Luli Group Co.,Ltd. , https://www.cnluli.com