(a) Decision
1, depending on the overall style
The choice of tiles depends mainly on the owner’s own tastes, tastes, consumption levels, etc., but can not blindly select, can not look on the line, pay attention to the type of tile, style and overall style of the indoor coordination. Larger spaces cannot use ceramic tiles with too small size, dark floors cannot use dark ceramic tiles, and kitchen and bathroom tiles must match the shapes and colors of kitchenware and sanitary ware.
Personally, I think what kind of tiles to choose depends on the overall design style. No matter how good the ceramic tiles do not match with the overall effect, it also means zero, indicating that this design is a failure. General introduction, kitchen and bathroom pre-determined wall tiles, reconfigured floor tiles, wall tiles with light-colored matt bricks, larger area with 300mm×450mm, smaller area with 250mm×330mm, decorative> decorative The bricks in the room usually use only 2-3 pieces, which will affect the effect.The tiles for kitchen and floor tiles should be used for non-slip tiles.The living room and bedroom are generally made of 600mm×600mm and 800mm×800mm tiles.
2, choose the regular brand
The color and texture of the matte brick are rich, and the paving effect is warm and elegant. It is resistant to dirt and slippery. Polished bricks have a high degree of finish, and in addition to the infiltration of polished tiles, there are micro-polished tiles. The surface of the micro-polished tiles is more delicate, with a higher degree of finish and stain resistance. The high-quality polished brick tiles have no sawtooth, no porcelain, pure color, clear pattern lines, no spread, and strong three-dimensional effect. When a consumer chooses a tile, he may use a nail or a key to scratch the surface of the tile. The hardness is high without leaving marks. It is also possible to splash the ink and tea on the surface. After 10 minutes, wipe it off. Dirty.
To choose the regular brand, regular brand tiles in addition to quality assurance, after-sales service is also perfect, if the tile is color, you can exchange free. Tile sales staff believes that the selection of vitrified tiles should be smooth, high-bright, and comfortable. Similarly, the identification of the impermeability of vitrified tiles can also be used "test ink" method. The 800m×800 vitrified tile that sells the fastest now is less and less people buy 600 mm×600 mm, and more and more people buy 1000 mm×1000 mm.
When picking tiles, the quality of the percussion sound is good; the general density with small water absorption is larger, and the density with the same specification is larger; the two tiles are overlapped to check the flatness of the tiles; the color difference of the tiles is measured. In addition, pay attention to the sample and the warehouse tile grade, color difference is the same. Also, consumers should buy a few more pieces of the actual budget to avoid color differences between batches, or buy them immediately if they are not enough.
3, check the test report
When selecting the tile, the fee maker can identify the quality of the tile by checking the inspection reports and certification certificates provided by the merchant. The test report is issued within six months. The final "judgment conclusion" of the test report must be passed, and the inspection agency issuing the test report must be authoritative. Test reports generally include chapters such as CMA (Measurement Certification), CAL (Certificate of Examination), and CNAL (National Laboratory Accreditation). The number of chapters reflects the qualifications of the inspection units. The CMA is the most basic and must have lower qualifications. The inspection unit does not have a CAL chapter, and the state-level and higher-quality provincial inspection units have the CNAL chapter. When viewing the certificate, the certificate must correspond to the sales product. This year, the 3C certification of the ceramic tile has started, 3C certification is the national unified certification standard, the previous other relevant certification will be unified to the 3C certification, through the 3C certified tiles, reliable Sex is better than average.
Ceramic tile radioactivity detection is based on the national mandatory standard for radionuclides of construction materials GB6566-2001, which mainly detects the radioactivity of radium, thorium and potassium. At present, there are very few radioactivity tests for regular brand tiles.
Tiles Optional Decoration Room Kitchen Wall Tiles Bathroom Tiles Bathroom Tiles Color Bathroom Tiles Bathroom Size Integral Bathroom Toilet Design Bathroom Tiles Small Bedroom Kitchen Tile Tiles Specifications
Coated abrasives have a wide variety of applications, from grinding applications toLook, one class is the manual use of varieties (sheet emery cloth, sandpaper andPartially rolled sandpaper); The other is for mechanical processing varieties(mainly belt, disc, wheel and ring).
1, large flat surface polishing, steel plate, plywood, leather.
2, mass production of workpiece surface sanding, printed circuit board, steel
Piano board, wooden furniture, etc.
3. Continuous polishing and grinding of metal strip. (Strip width ok
Above 1200mm, length is unlimited)
4, forming grinding and polishing of complex surface work.
5, all kinds of diameter metal tube, rod, roller cylindrical grinding and large diameter
In 25mm container, internal circular grinding such as: cylinder, hydraulic cylinder oil tank
And so on.
6, the page wheel and sand ring can replace polishing cloth wheel, realize polishing process automation.
7. Sand plate is used for grinding welding seam of large shell, box body and hull
Burr, paint, etc.
Coated Abrasive,Flap Wheel,Sanding Paper,Sanding Belts
Henan Jinlun Superhard Material Co., Ltd , https://www.jinlunsuperhard.com